Difference between revisions of "Fusion welding of optical fibres/fr"

[pending review revision][pending review revision]
(Page créée avec « Préparation des accessoires »)
(Page créée avec « Matériel nécessaire : soudeuse, cliveuse, pince à dénuder, lingettes non pelucheuses, alcool isopropylique et protections d'épissure thermorétractables (smooves). »)
Line 25: Line 25:
 
{{Tuto Step
 
{{Tuto Step
 
|Step_Title=Préparation des accessoires
 
|Step_Title=Préparation des accessoires
−
|Step_Content=Tools required: fusion splicer, clipper, stripper, lint-free wipes, isopropyl alcohol and heat-shrinkable splice guards (smooves).
+
|Step_Content=Matériel nécessaire : soudeuse, cliveuse, pince à dénuder, lingettes non pelucheuses, alcool isopropylique et protections d'épissure thermorétractables (smooves).
 
|Step_Picture_00=Fusion_welding_of_optical_fibres_img68.jpg
 
|Step_Picture_00=Fusion_welding_of_optical_fibres_img68.jpg
 
|Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-82,"top":-3,"width":800,"height":442,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/5/57/Fusion_welding_of_optical_fibres_img68.jpg","filters":[]}],"height":449.42528735632186,"width":600}
 
|Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-82,"top":-3,"width":800,"height":442,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/5/57/Fusion_welding_of_optical_fibres_img68.jpg","filters":[]}],"height":449.42528735632186,"width":600}

Revision as of 15:29, 7 June 2019

Réaliser une soudure de câble Fibre Optique.

Author avatarAlexiane Philip | Last edit 7/06/2019 by Alexiane under review

Difficulty
Medium
Duration
10 minute(s)
Area
Use
Business
Training
Réaliser une soudure de câble Fibre Optique.
Difficulty
Medium
Duration
10 minute(s)
Area
Use
Business
Training
Other languages:
English • ‎français

Items

Fusion splicer
Item-Fusion splicer s-l300.jpg
The fusion splicer is a tool which delivers fast and reliable fibre splicing under even harsh environmental conditions. It combines portability and ease of use in a ruggedized body.
Clipper
Item-Clipper 31Y2dhR CXL. SR600 315 PIWhiteStrip BottomLeft 0 35 SCLZZZZZZZ .jpg
The clipper is an instrument for cutting or trimming small pieces of things.
Isopropyl alcohol
Item-Isopropyl alcohol 61I2R8Tot L. SY355 .jpg
Isopropyl alcohol is a colorless, flammable chemical compound with a strong odor. It dissolves a wide range of non-polar compounds. Thus, it is used widely as a solvent and as a cleaning fluid, especially for dissolving oils.

Step 1 - Préparation des accessoires

Matériel nécessaire : soudeuse, cliveuse, pince à dénuder, lingettes non pelucheuses, alcool isopropylique et protections d'épissure thermorétractables (smooves).




Step 2 - Stripping and cleaning the fibre

Strip 3/4 cm of the fibre. Clean the bare fibre with isopropyl alcohol before cleaving.

NB: do not touch the fibre with your fingers once it has been cleaned.


Step 3 - Cleavage of the fibre

Position the fibre in the appropriate slot of the fibre guide (250 or 900 µm), the sheath 250 or 900 µm at scale 10, making sure that the devoid part rests firmly on the 2 pads.



Step 4 - Positioning the fibre in the welder

Position the fibre in the fusion splicer by placing its end between the alignment of the electrodes and the edge of the V-slot, close the valve retaining the fibre.

NB: Be careful not to hit the end of the fibre as this may alter the quality of the cleavage.

You must now repeat these operations for the second fibre.


Step 5 - Choosing the programs of the welder machine

Use the welding program adapted to the type of fibre to be welded, as well as the furnace program adapted to the type of smoove used.

Example: Single mode MS, multi-mode MM and single mode BIF G657.

Step 6 - Welding process

Close the cover to initiate the welding process (the auto start function must be activated otherwise press the green arrow on the keyboard).


Step 7 - Welding evaluation

Three evaluation criteria should be observed: the image quality of the welded fibres (good alignment of the cores, absence of dust or air bubbles, etc.), the estimated loss given by the fusion splicer and the resistance of the fibre to the tensile test (not to be disabled).


Step 8 - Positioning the smoove and shrinkage

Before opening the cover, bring the smoove as close as possible to the fusion splicer, center it at the weld, making sure that the shrinkage will be on the fibre protection sheaths and not on the bare fibre. Position the smoove in the center of the furnace. The furnace is activated automatically if this function has been previously selected in the machine parameters, otherwise press the yellow resistance on the keyboard.


Step 9 - Positioning the smoove on a cassette for winding

After shrinking, position the smoove on the cooling plate before welding other fibres. Then place the smooves in the cassette and wind the fibres.



Comments

Published

Retrieved from "https://demo.dokit.io/w/index.php?title=Fusion_welding_of_optical_fibres/fr&oldid=3590"
© 2017 - 2024 Dokit, SAS.