Difference between revisions of "Fusion welding of optical fibres"

[pending review revision]

Revision as of 15:06, 7 June 2019

Weld a Fibre Optic cable.

Author Alexiane Philip | Last edit 7/06/2019 by Alexiane under review ⧼frevu-button-review-label⧽

Difficulty

Medium

Duration

10 minute(s)

Area

Use

Business

Training

Weld a Fibre Optic cable.

Difficulty

Medium

Duration

10 minute(s)

Area

Use

Business

Training

Other languages:

English • ‎français

1 Step 1 - Preparation of the accessories
2 Step 2 - Stripping and cleaning the fibre
3 Step 3 - Cleavage of the fibre
4 Step 4 - Positioning the fibre in the welder
5 Step 5 - Choosing the programs of the welder machine
6 Step 6 - Welding process
7 Step 7 - Welding evaluation
8 Step 8 - Positioning the smoove and shrinkage
9 Step 9 - Positioning the smoove on a cassette for winding
10 Comments

Install

Step 1 - Preparation of the accessories

Tools required: welder machine, clipper, stripper, lint-free wipes, isopropyl alcohol and heat-shrinkable splice guards (smooves).

Step 2 - Stripping and cleaning the fibre

Strip 3/4 cm of the fibre. Clean the bare fibre with isopropyl alcohol before cleaving.

NB: do not touch the fibre with your fingers once it has been cleaned.

Step 3 - Cleavage of the fibre

Position the fibre in the appropriate slot of the fibre guide (250 or 900 µm), the sheath 250 or 900 µm at scale 10, making sure that the devoid part rests firmly on the 2 pads.

Step 4 - Positioning the fibre in the welder

Position the fibre in the welder machine by placing its end between the alignment of the electrodes and the edge of the V-slot, close the valve retaining the fibre.

NB: Be careful not to hit the end of the fibre as this may alter the quality of the cleavage.

You must now repeat these operations for the second fibre.

Step 5 - Choosing the programs of the welder machine

Use the welding program adapted to the type of fibre to be welded, as well as the furnace program adapted to the type of smoove used.

Example: Single mode MS, multi-mode MM and single mode BIF G657.

Step 6 - Welding process

Close the cover to initiate the welding process (the auto start function must be activated otherwise press the green arrow on the keyboard).

Step 7 - Welding evaluation

Three evaluation criteria should be observed: the image quality of the welded fibres (good alignment of the cores, absence of dust or air bubbles, etc.), the estimated loss given by the machine and the resistance of the fibre to the tensile test (not to be disabled).

Step 8 - Positioning the smoove and shrinkage

Before opening the cover, bring the smoove as close as possible to the welder, center it at the weld, making sure that the shrinkage will be on the fibre protection sheaths and not on the bare fibre. Position the smoove in the center of the furnace The furnace is activated automatically if this function has been previously selected in the machine parameters, otherwise press the yellow resistance on the keyboard.

Step 9 - Positioning the smoove on a cassette for winding

After shrinking, position the smoove on the cooling plate before welding other fibres. Then place the smooves in the cassette and wind the fibres.

Comments

en none 0 Published

@@ Line 2: / Line 2: @@
 |Main_Picture=Fusion_welding_of_optical_fibres_img15.jpg
 |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-42,"top":-2,"width":800,"height":440,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/a/a2/Fusion_welding_of_optical_fibres_img15.jpg","filters":[]}],"height":449.7131931166348,"width":600}
-|Description=<translate>Weld a Fibre Optic cable.</translate>
+|Description=<translate><!--T:1--> Weld a Fibre Optic cable.</translate>
 |Categories=Work instructions
 |Difficulty=Medium
@@ Line 16: / Line 16: @@
 {{Materials}}
 {{Tuto Step
-|Step_Title=<translate>Preparation of the  accessories</translate>
+|Step_Title=<translate><!--T:2--> Preparation of the  accessories</translate>
-|Step_Content=<translate>Tools required: welder machine, clipper, stripper, lint-free wipes, isopropyl alcohol and heat-shrinkable splice guards (smooves).</translate>
+|Step_Content=<translate><!--T:3--> Tools required: welder machine, clipper, stripper, lint-free wipes, isopropyl alcohol and heat-shrinkable splice guards (smooves).</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img68.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-82,"top":-3,"width":800,"height":442,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/5/57/Fusion_welding_of_optical_fibres_img68.jpg","filters":[]}],"height":449.42528735632186,"width":600}
 }}
 {{Tuto Step
-|Step_Title=<translate>Stripping and cleaning the fibre</translate>
+|Step_Title=<translate><!--T:4--> Stripping and cleaning the fibre</translate>
-|Step_Content=<translate>Strip 3/4 cm of the fibre. Clean the bare fibre with isopropyl alcohol before cleaving.
+|Step_Content=<translate><!--T:5-->
+Strip 3/4 cm of the fibre. Clean the bare fibre with isopropyl alcohol before cleaving.
+<!--T:6-->
 '''NB:''' do not touch the fibre with your fingers once it has been cleaned.</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img70.jpg
@@ Line 35: / Line 37: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Cleavage of the fibre</translate>
+|Step_Title=<translate><!--T:7--> Cleavage of the fibre</translate>
-|Step_Content=<translate>Position the fibre in the appropriate slot of the fibre guide (250 or 900 µm), the sheath 250 or 900 µm at scale 10, making sure that the devoid part rests firmly on the 2 pads.</translate>
+|Step_Content=<translate><!--T:8--> Position the fibre in the appropriate slot of the fibre guide (250 or 900 µm), the sheath 250 or 900 µm at scale 10, making sure that the devoid part rests firmly on the 2 pads.</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img76.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-114,"top":-1,"width":800,"height":442,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/8/8a/Fusion_welding_of_optical_fibres_img76.jpg","filters":[]}],"height":450.5703422053232,"width":600}
@@ Line 43: / Line 45: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Positioning the fibre in the welder</translate>
+|Step_Title=<translate><!--T:9--> Positioning the fibre in the welder</translate>
-|Step_Content=<translate>Position the fibre in the welder machine by placing its end between the alignment of the electrodes and the edge of the V-slot, close the valve retaining the fibre.
+|Step_Content=<translate><!--T:10-->
+Position the fibre in the welder machine by placing its end between the alignment of the electrodes and the edge of the V-slot, close the valve retaining the fibre.
+<!--T:11-->
 '''NB''': Be careful not to hit the end of the fibre as this may alter the quality of the cleavage.
+<!--T:12-->
 {{Info|You must now repeat these operations for the second fibre.}}</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img98.jpg
@@ Line 57: / Line 62: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Choosing the programs of the welder machine</translate>
+|Step_Title=<translate><!--T:13--> Choosing the programs of the welder machine</translate>
-|Step_Content=<translate>Use the welding program adapted to the type of fibre to be welded, as well as the furnace program adapted to the type of smoove used.
+|Step_Content=<translate><!--T:14-->
+Use the welding program adapted to the type of fibre to be welded, as well as the furnace program adapted to the type of smoove used.
+<!--T:15-->
 Example: Single mode MS, multi-mode MM and single mode BIF G657.</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img115.jpg
@@ Line 74: / Line 81: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Welding process</translate>
+|Step_Title=<translate><!--T:16--> Welding process</translate>
-|Step_Content=<translate>Close the cover to initiate the welding process (the auto start function must be activated otherwise press the green arrow on the keyboard).</translate>
+|Step_Content=<translate><!--T:17--> Close the cover to initiate the welding process (the auto start function must be activated otherwise press the green arrow on the keyboard).</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img137.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-65,"top":-5,"width":800,"height":446,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.02,"scaleY":1.02,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/f/f5/Fusion_welding_of_optical_fibres_img137.jpg","filters":[]}],"height":450,"width":600}
@@ Line 84: / Line 91: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Welding evaluation</translate>
+|Step_Title=<translate><!--T:18--> Welding evaluation</translate>
-|Step_Content=<translate>Three evaluation criteria should be observed: the image quality of the welded fibres (good alignment of the cores, absence of dust or air bubbles, etc.), the estimated loss given by the machine and the resistance of the fibre to the tensile test (not to be disabled).</translate>
+|Step_Content=<translate><!--T:19--> Three evaluation criteria should be observed: the image quality of the welded fibres (good alignment of the cores, absence of dust or air bubbles, etc.), the estimated loss given by the machine and the resistance of the fibre to the tensile test (not to be disabled).</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img143.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-83,"top":-2,"width":800,"height":433,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.06,"scaleY":1.06,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/2/21/Fusion_welding_of_optical_fibres_img143.jpg","filters":[]}],"height":449.706457925636,"width":600}
@@ Line 94: / Line 101: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Positioning the smoove and shrinkage</translate>
+|Step_Title=<translate><!--T:20--> Positioning the smoove and shrinkage</translate>
-|Step_Content=<translate>Before opening the cover, bring the smoove as close as possible to the welder, center it at the weld, making sure that the shrinkage will be on the fibre protection sheaths and not on the bare fibre. Position the smoove in the center of the furnace The furnace is activated automatically if this function has been previously selected in the machine parameters, otherwise press the yellow resistance on the keyboard.
+|Step_Content=<translate><!--T:21-->
+Before opening the cover, bring the smoove as close as possible to the welder, center it at the weld, making sure that the shrinkage will be on the fibre protection sheaths and not on the bare fibre. Position the smoove in the center of the furnace The furnace is activated automatically if this function has been previously selected in the machine parameters, otherwise press the yellow resistance on the keyboard.
+<!--T:22-->
 <br /></translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img164.jpg
@@ Line 110: / Line 119: @@
 }}
 {{Tuto Step
-|Step_Title=<translate>Positioning the smoove on a cassette for winding</translate>
+|Step_Title=<translate><!--T:23--> Positioning the smoove on a cassette for winding</translate>
-|Step_Content=<translate>After shrinking, position the smoove on the cooling plate before welding other fibres. Then place the smooves in the cassette and wind the fibres.</translate>
+|Step_Content=<translate><!--T:24--> After shrinking, position the smoove on the cooling plate before welding other fibres. Then place the smooves in the cassette and wind the fibres.</translate>
 |Step_Picture_00=Fusion_welding_of_optical_fibres_img186.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-55,"top":-1,"width":800,"height":549,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.82,"scaleY":0.82,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"http://demo-master.dokit.io/w/images/6/6c/Fusion_welding_of_optical_fibres_img186.jpg","filters":[]}],"height":449.7709923664122,"width":600}